These are instructions on how to root Samsung Galaxy Note 10.1 SM-P600 (running on android 5.1.1, built id LMY47X.P600UBUDPB1 or LMY47X.P600UEUDOK1) using Odin on Windows Computer.
Requirements: Your Samsung Galaxy Note 10.1 SM-P600 should have at least 30-40 percent of battery to perform the rooting process.
Root Samsung Galaxy Note 10.1 SM-P600 using Odin
- Download and Install Samsung USB Driver on the computer. If in case Samsung USB Drivers are already installed on the computer, then SKIP this step.
- Download (LMY47X.P600UBUDPB1) or Download (LMY47X.P600UEUDOK1) and extract the root files on the computer. Once the archive is extracted, you will be able to see the following files:
- Enable Developer Options on your Samsung mobile. To Enable Developer Options: Open Settings > About Phone > Tap on the Built Number for 6-8 times until developers option is enabled.
- Enable OEM unlock on your Samsung mobile. To Enable OEM Unlock: Open Settings > Developer Options > Tap on the OEM unlocking checkbox > Tap on Enable > Tap on Delete All button.
- Now, Switch off your Phone.
Step 4: Now, you have to enable Download Mode on your phone. To enable download mode Press and hold Volume Down Key and Power key at same time for 5-8 seconds (you have to press and hold all three buttons at same time) until download mode is not active.
- In the Download mode you will be able to see a Warning Yellow Triangle Sign. In this situation you have to press the Volume up key to continue.
- Now, Open Odin3 (found in the extracted files, that you have downloaded in the Step#2) on your computer. Then connect your phone to the computer.
- Once you have connected the phone to the computer, Odin will automatically recognize the device and show “Added” message at the lower-left panel.
- Once your device detected by Odin, click on the PDA button and select the CF-Auto-Root.tar.md5 file (you have downloaded this file in step#2).
- Now, click on the Start button in Odin to begin the Flashing.
- Flashing usually takes 30-50 seconds to complete the rooting process on your Samsung Galaxy Note 10.1 SM-P600. Once Rooting process got completed, you will be able to see a Green Box with Pass written on it in Odin. During this process phone will re-boot automatically.
- Once you see, the Pass message in Odin, you can disconnect your Device from the computer.
- Now, to make sure you have successfully rooted your Samsung Galaxy Note 10.1 SM-P600, open Applications Menu on your phone and Find SuperSU App. If this app exist on your phone then it means you have successfully rooted your device. Congratulations.
Optional: You can also verify the root status of your device by using the Root Checker App.
Notes
[*] Warning: The above tutorial only works for Android 5.1.1 with the built id LMY47X.P600UBUDPB1 or LMY47X.P600UEUDOK1.
[*] If your device isn’t running on the same built id LMY47X.P600UBUDPB1 or LMY47X.P600UEUDOK1, then you may need to download and flash (install) the firmware based on the same build id. Later try to root your device from the above method.
[*] No data loss process: Your Phone Data like contacts, pictures, videos, music and etc will be not affected with the above method. In short, no data loss process.
[*] Samsung Stock Firmware: If you are looking for the original firmware for your device, then head over to Download Samsung Stock Firmware page.
[*] Samsung USB Driver: If you are looking for the original USB Driver for your device, then head over to Download Samsung USB Driver page.
[*] Big thanks to Chainfire for their CF Auto Root file for Samsung Galaxy Note 10.1 SM-P600. Without using the CF-Auto Root file, the above tutorial was not possible.